Epoxy grout (solution type) 1. mix can be used at room temperature without adding any additional ingredients. Strength non-shrink epoxy grout to need long-term secondary grouting equipment to withstand vibration, shock and chemical corrosion zones installed to provide a permanent solution has been proven to greatly extend continuously moving equipment running solid phase and component life. 2. Features (1) high-strength early strength: physical and mechanical properties of compression, bonding and other far better than ordinary cement-based grout. (2) the gravity of: fill all the gaps, meet the requirements of secondary grouting equipment. (3) No shrink: to ensure close contact between the equipment and infrastructure to ensure the precision required for installation. (4) water milk epoxy cement base: epoxy resin with high quality cement together, durability and meet environmental protection requirements. (5) corrosion resistance: can withstand acid, alkali, salt, oil and other chemicals, long-term contact corrosion. (6) creep resistance: long-term use without plastic deformation in bad physical condition, to ensure long-term precision positioning equipment. Secondary 3. Uses for compressors, pumps, press, grinder, ball mill, high vibration equipment grout installation. Susceptible to chemical attack for equipment foundation grouting area. Foundation for track, bridges and other supporting base area by the strong pressure grouting. Anchor steel for planting and construction of structural concrete reinforcement. It can be used in wet grass. Strong bond. The performance range of test report test results 1 Fluidity (mm) 245 2 vertical expansion rate (%) ≥0.02 3 28d flexural strength (Mpa) ≥6.0 4 28d neutral resistance (mm) <5.0 5 anti- compressive strength (Mpa) 3d ≥20 6 7d ≥40 7 28d ≥60 8 reinforced the bond strength (Mpa) round steel ≥13 ≥6 9 Notes: (1) Compressive strength: According to "GB177-85 cement mortar strength test. " (2) expansion: according to "GB119-88 concrete admixture technical specifications" 5. Construction guidelines (a) Surface preparation: Contact strength non-shrink epoxy grout concrete surface shall be chiseled surface laitance and expose solid grassroots level, to ensure the grout surface clean, dry and free of grease. Concrete joints grind the outer edge of the 25mm thick bevelled edges to increase the edge of the grout and adhesive base area; the need to bond metal surfaces should be no rust (up sspc-sp6 finish on request). (B) the formwork: template shall be strong lap firm, its inside with grease, wax or paste pvc tape in order to release; for ease of installation dumping and filling funnel, filling side between the template and equipment around the base of leaving at least 100mm distance, and more than 100mm above the equipment chassis. In the template on the inside of the filling level height 25mm thick nails 45 degree angle Mouldings, avoid pouring body edge stress concentration. (C) Application temperature: Ambient including concrete base and air temperature. For the best working conditions, the construction and the subsequent 24 hours at ambient temperature is best controlled 15 ° C ~ 32 ° C, 20 ° C is most appropriate. Summer construction to avoid the midday heat, when necessary, to build awning; winter temperature is low, should be raised to build greenhouses in the filling area, to ensure that environmental temperature is greater than 15 ° C, the construction should choose noon. (Iv) Ingredients: (1) for providing a stirrer (200-250rpm) first A material, B material stir respectively (long-term placement precipitation phenomenon), then follow A material: B feed = 1: 3 the proportion of fully mixed and stirred for about 3 minutes. (2) high-power mixer at low speed (15-20rpm) added C material, the A material, B material, C material fully mixed, mix for about 5-10 minutes; in order to ensure the flow of the mixture at low temperatures sex, may be appropriate to reduce the amount of C material or appropriate to add water and stir well. (E) filling method (1) filling grout should side to side; grouting process can squeeze but do not vibrating, in order to avoid inclusion of air trapping therein; grouting distance is greater than 1.5m, high filling funnel method should be used, Filling pressure assisted gravity principle. (2) The grout work must be completed as soon as continuous. (3) Single grout layer thickness control in between 25mm ~ 350mm; single bolt hole filling depth is less than 1500mm; filling volume exceeding 1.8m * 1.8m * when 150mm, need to grab the sticky surface wipe board on the basis of pre-set joints stay shall, after filling the final setting of the surface portion thereof except to pull, then sealed material joints. 6. Packing ☆ A material: plastic bucket 15kg / barrel ☆ B material: plastic bucket 45kg / barrel ☆ C material: paper bag 450kg / bags with weight ratio ☆ Use: (A + B + C = 1: 3: 30) ☆ Each group net 510kg. 7. Storage and Transport (1) The product A milk feed B feed water emulsion epoxy and hardener emulsions should be stored above 5 ° C in the shade under a sealed condition, the shelf life of six months. C material for the polymer dry mortar, should be stored in a dry environment moisture, not under state Kaifeng shelf life of six months. (2) non-flammable, non-explosive, non-polluting and radiological hazards, according to general cargo storage and transportation.